T100 - Heating Circulator

Product Calibration

A product calibration service is available which includes a calibration certificate, traceable to national standards.  Please enquire prior to placing order. 

T-CLAMP


Clamp allows heating circulator to be attached to virtually any vertical sided vessel with a maximum wall thickness of 35mm for rectangular tanks, 30mm for circular tanks (300mm diameter), and capacity up to 50L. 

ST Stainless Steel and P Plastic Tanks
Capacity (L) Outer tank dimensions

Working area
(d x w)

Min/max liquid depths

Inner tank dimensions
(d x w x h)

ST5 - 5 L stainless steel

150 x 150 mm

85/140 mm

300 x 150 x 150 mm

ST12 - 12 L stainless steel

205 x 300 mm

85/140 mm 

325 x 300 x 150 mm

ST18 - 18 L stainless steel

385 x 300 mm

75/130** mm 

505 x 300 x 150 mm

ST26 - 26 L stainless steel

385 x 300 mm

125/180** mm

505 x 300 x 200 mm 

ST38 - 38 L stainless steel

575 x 300 mm

125/180** mm 

690 x 300 x 200 mm 

P5 - 5 L plastic

120 x 150 mm

85/140 mm

240 x 160 x 155 mm

P12 - 12 L plastic

210 x 280 mm

85/140 mm 

325 x 280 x 155 mm 

P18 - 18 L plastic

280 x 375 mm

85/140 mm 

510 x 290 x 155 mm 

Accessories

Lids*
to help reduce evaporation/heat loss and avoid sample contamination

Lids
For continuous use with water above 90°C. Stainless steel.

Polypropylene spheres*
300 spheres in one pack (no. of packs required)
Rack systems †
to optimise use of available bath capacity (no. of racks accommodated)
Raised shelves
to allow shallow vessels to be accommodated
Accessory cooling systems**
to allow systems to operate at or below ambient temperature by means of a cooling coil dipped into the bath; designed for minimal impact on working area
Refrigerated immersion coolers
Consist of a cooling coil connected to a refrigeration unit by a flexible pipe. Extract heat continuously, with the bath control unit controlling temperature
Heat exchange coil
Designed to be attached to a supply of cooling tap water or a refrigerated circulator

C1G 
(0 to 40°C***)

C2G 
(- 15 to 40°C***)

CW5 
(2°C above coolant temperature)

STL5
flat stainless steel
 - 1 x PS20 1 x QR - YES - YES
STL12
gabled, hinged (removable) stainless steel

LST12

1 x PS20 2 x VR RS14 YES - YES
STL26 for ST18 tank
gabled, hinged (removable) stainless steel
LST26
2 x PS20 4 x VR RS22 YES - YES

STL26 for ST26 tank 
gabled, hinged (removable) stainless steel

LST26

2 x PS20 4 x VR RS28 YES YES YES
STL38
gabled, hinged (removable) stainless steel
LST38
3 x PS20 6 x VR RS28 or RS38 YES YES YES
PL5
flat, stainless steel
 - 1 x PS20 1 x QR - - - -
PL12
curved plastic
 - 1 x PS20 2 x VR RS14 (h 40 or 78mm) - - -
PL18
curved plastic
 - 2 x PS20 4 x VR RS22 (h 40 or 78mm) - - -
* Between operating temperatures 60°C and 100°C and below room temperature a lid or layer of polypropylene spheres should be used. 
** The cooling coil can be continuously immersed in liquids up to 100°C with the cooler switched off, and may be used to cool liquid down from 100°C, but it is not designed for continuous operation above 40°C.
*** Minimum operating temperature without accessory cooling is ambient + 5°C,  (amb. + 15°C for P5 and ST5 tanks).
† Rack capacity (no. of test tubes per rack)
 
VR racks   Tube size Capacity   QR racks Tube size Capacity
VR-13   Ø10-13 mm 65   QR-13 Ø10-13 mm 30
VR-19   Ø16-19 mm 36   QR-19 Ø16-19 mm 16
VR-24   Ø24 mm 23   QR-24 Ø24 mm 10
VR-30   Ø30 mm 14   QR-30 Ø30 mm 5
VR-SE   0.5 ml 102   QR-SE 0.5 ml 44
VR-LE   1.5ml 75   QR-LE 1.5 ml 35

CG refrigerated immersion coolers  (to use in combination with ST stainless steel tanks)

Refrigerated coolers consist of a cooling coil connected by a flexible pipe to a refrigeration unit, which is housed in an outer case; immersion coolers extract heat continuously, with temperature control carried out by the bath's control unit.

CW5 heat exchange coil: is designed to be attached to a supply of cooling tap water, or a refrigerated circulator.

Grant accessory cooling systems for combination with ST stainless steel tanks

 Immersion coolersHeat exchange coil
C1GC2GCW5
Cooling power @ 20°C W 350 400 -
  @ 0°C W 110 320 -
  @ - 10°C W - 170 -
Overall consumption   VA 300 500 -
Dimensions d/w/h mm 460/305/225 -
Weight   kg 17 21  0.1
Flexible pipe l mm 925 925 -
Coil Ø/l mm 77/55 77/55 77/55
Pipe bore inlet/outlet   mm - - 7
Electrical supply    V 120 (60 Hz) or 230 (50Hz) -
Refrigeration units
Capacity (L)
Outer tank dimensions

Working area
(d x w)

Min/max liquid depths 

Weight 

R4 - 20 L stainless steel

230 x 305 mm

85/140 mm

40.6 kg

R5 - 12 L stainless steel

260 x 115 mm

125/180 mm

48.3 kg

 

Pump Connectors (optional)
 

Part number

Replacement plastic pump inlet/outlet connector. Fits tubing 9mm inner dia. Temp range -50 to 200˚C

P-M6

Replacement plastic pump inlet/outlet connector. Fits tubing 15mm inner  dia. Temp range -50 to 200˚C

P-M11

Stainless steel pump inlet/outlet connector, M16 x 1 male. Fits M16 hose. Temp range -50 to 200˚C

M-M16

Metal pump inlet/outlet connector, dual seal super rapid 4mm. Fits semi rigid tubing 4mm outer dia. Temp range -20 to 100˚C

M-SR4

Metal pump inlet/outlet connector, dual seal super rapid 6mm. Fits semi rigid tubing 6mm outer dia. Temp range -20 to 100˚C

M-SR6

Metal pump inlet/outlet connector, dual seal super rapid 8mm. Fits semi rigid tubing 8mm outer dia. Temp range -20 to 100˚C

M-SR8

Metal pump inlet/outlet connector, hose barb 7mm. Fits flexible tubing 7mm inner dia. Temp range -40 to 120˚C

M-HB7

Metal pump inlet/outlet connector, hose barb 9mm. Fits flexible tubing 9mm inner dia. Temp range -40 to 120˚C

M-HB9

Metal pump inlet/outlet connector, hose barb 12mm. Fits flexible tubing 12mm inner dia. Temp range -40 to 120˚C

M-HB12

Metal pump inlet/outlet plate, 1/4 " BSP/G1/4 female. Temp range -50 to 200˚C

M-UC